Windsor Chairmakers : 18th century highboy

Shipping options. Select the level of service you desire that is available for each and all the pieces in your order.

After shipping is complete, we will pay the shipping company on your behalf, charge that exact amount against your prepayment, and send you a refund check of any overpayment.

White glove blanket wrapped service- Furniture set up in room ready to use. No packing required.

Delivery in company van in Maine- Furniture set up in your room ready to use. No packing required.

Customer pick up- From loading dock at workshop. No packing required.

Call Suzanne for quote
800-789-5188

9am - 5pm EST

close

Shell.
This style is more specifically known as a Connecticut fan shell. Each one is hand carved by Valdomeyr Skov, a highly skilled craftsman living here in Maine. He uses only hand chisels and a mallet. The small imperfection left by the chisel can only be obtained by doing this by hand.

Pine as secondary wood. In the 18th century, it was common for pine to be used on the interior parts of chests. this practice significantly reduced the weight of the chest when it needed to be moved. Pieces such as highboys benefited from pine as the secondary wood by the reduction of weight on the slim ankles of the cabriole legs.

Hand cut dovetails.
Dovetails are the preferred method of holding drawers together. They are made either with a router and jig or hand cut with a saw. Hand cutting with a saw replicates the method used in the 18th century. This is the method we use.
Hand cutting requires more skill but quicker. A router and jig requires less skill and more time. This is particularly true when using graduated drawer heights and the height of each drawer is different.

One piece drawer bottoms. In the 18th century there were more big trees than time to glue and clamp drawer bottoms together. Consequently, drawer bottoms were made out of one piece of wood. We do the same. It doesn't make the drawer bottoms any better, just more authentic.

Varnish.

Better than lacquer, shellac, or linseed oil as a top coat. It does not allow water to penetrate into the wood and cause a white spot. We use two coats to be surer that we have the surface entirely covered.

Sand cast brass hardware.
Today, hardware is made three ways. It is either sand cast, or dye cast, or stamped. In the 18th century all hardware was sand cast. This is the process our supplier uses for us. It imparts a subtle irregularity that can not be duplicated by either of the other two methods.
A model is made and packed in French sand. The sand mold is opened, the model taken out and brass poured in. When the piece has cooled, it is taken out and polished. When the piece of hardware gets dull again due to exposure to air, you may have the fun of polishing it also. I suggest you use polishing wool and do not take the pieces off the furniture.

Antiquing. The combination of steps in the furniture finishing process that have as their sole objective to make the furniture look older than it really is. How much older is determined by the amount of antiquing applied. We offer antiquing in light, medium and heavy quantities.
The lowest level of antiquing is "light", not "none". There are three reasons for this.

First, try as we might to make perfect furniture with no blemishes, we can't. So, rather than promise you something that we can't do, we offer you the best that we can do.

Second, scratches and dings will happen to your furniture as you use it. if we put the first few on, as others occur, there is less anxiety which is good for you and your visitors.

Third, we think it looks more appropriate. It's like a person over forty-five having crows feet around their eyes.

Hand rubbed finish.

After the final coat of flat varnish has been applied and allowed to cure or get hard, the surface is rubbed with 400 grit sandpaper. This removes the dust fleckles that fell into the varnish before it completely dried. It also softens the appearance and feel of the finish to a very desirable luster. It's a time consuming process but we feel that it's worth it.

Ordering.

We'd like to hear from you, so call us at 800-789-5188 or email info@windsorchair.com. If you'd like samples, we can send a variety with a $200 deposit, refundable upon return of the samples.

Cash and checks are preferred. Visa and Mastercard are accepted.